 Essay Writing Service - Force Essays and Research Papers | examples.essaytoday.biz     # Force Essays & Research Papers

## Best Force Essays

• Force - 2731 Words
What is Force? In physics, a force is any influence that causes an object to undergo a certain change, either concerning its movement, direction, or geometrical construction. It is measured with the SI unit of newtons and represented by the symbol F. In other words, a force is that which can cause an object with mass to change its velocity(which includes to begin moving from a state of rest), i.e., to accelerate, or which can cause a flexible object to deform. Force can also be described by...
2,731 Words | 9 Pages
• forces - 2812 Words
Chapter 2 Forces To study the effect of forces acting on particles. 2.1 Equilibrium of a Particle 2.2 Free Body Diagram 2.3 Force Vectors 2.4 Forces in a Plane 2.5 Forces in Space Expected Outcomes • Understand the condition for a particle to be in static equilibrium • Able to construct free body diagrams • Able to solve for the forces acting on a static particle 2.1 Equilibrium of a Particle www.classical.com/features 2.1.1 Condition for the Equilibrium of a...
2,812 Words | 29 Pages
• Force - 9491 Words
® keep it simple science ABN 54 406 994 557 (02) 6583 4333 PO Box 2575 PORT MACQUARIE NSW 2444 FAX (02) 6583 9467 www.keepitsimplescience.com.au [email protected] keep it simple science Photocopy Master Sheets Years 7-8 FORCES Disk filename = “02.Forces” Copying is permitted according to the Site Licence Conditions only 1 Site Licence Conditions Our product is supplied on CD • You may copy the CD for back-up only. • You may store the CD...
9,491 Words | 43 Pages
• Net Force - 292 Words
1. Two ropes are attached to a wagon, one horizontal to the west with a tension force of 30 N, and the other east and at an angle of 30° northward and a tension force of 40 N. Find the components of the net force on the cart. Show all your work. Answer: Horizontal Net Force = 40sin(30) – 30 Horizontal Net Force = -10 Vertical Net Force = 40cos(30) Vertical Net Force = 34.6 Use the Pythagorean theorem = a^2+b^2=c^2 Resultant Force = (-102) + (34.62) = C2 = 33.1 N at 30o...
292 Words | 2 Pages
• ## All Force Essays

• Force and Kg - 384 Words
More Equilibrium Problems 1. A uniform 25 kg bar, 6.0 m long, is suspended by a cord as shown. What is the tension in the cord? 270 N 2. A boom hinged at P is held stationary, as shown in the diagram below. If the tension in the supporting cord, attached three-quarters of the way along the boom from P, is 720 N, what is the weight of the boom? 2160 N 3. A uniform beam 6.0 m long, and with a mass of 75 kg, is hinged at A. The...
384 Words | 2 Pages
• Force and Container - 306 Words
﻿ Buoyancy, Force, and Gravity Purpose: To check the buoyancy of the object measured in Newton. Hypothesis: I think the force pulling down on the clay might be heavier then the container with water and clay. Apparatus: 1 small beaker (mL) 1Graduated cylinder 1 container 1 small portion of clay can Spring scale (newtons) Tap water 1 Cloth Method: First, hang the clay on the hook of the Newton spring scale. Secondly, record the measurements. Thirdly, get a container, fill...
306 Words | 2 Pages
• Force and Acceleration - 17605 Words
Chapter 4 Newton’s Laws Conceptual Problems 1 • While on a very smooth level transcontinental plane flight, your coffee cup sits motionless on your tray. Are there forces acting on the cup? If so, how do they differ from the forces that would be acting on the cup if it sat on your kitchen table at home? Determine the Concept Yes, there are forces acting on it. They are the normal force of the table and the gravitational pull of Earth (weight). Because the cup is not accelerating relative to...
17,605 Words | 82 Pages
• Centripetal Forces - 368 Words
While the bob is moving in the circular motion, the centripetal force that is provided is the spring. The spring causes the bob to get pulled inward and while it is being pulled inward while being rotated it provides a centripetal force. If this force was suddenly removed, the Bob would still have a centripetal force due to the rope in which it hangs from causing the inward force to keep moving in a circle. But if the forces are removed than its inertia would keep it moving in a straight line at...
368 Words | 1 Page
• Force & Motion - 930 Words
﻿Force & Motion Isaac Newton – English physicist & mathematician. Newton’s First Law of Motion(Law of Inertia): An object at rest stays at rest and an object in motion stays in motion with the same speed and in the same direction unless acted upon by an unbalance force. An object at rest tends to remain at rest. An object in motion tends to move at a constant speed in a straight line unless acted upon by an unbalanced external force. Newton’s Second Law of Motion(Law of...
930 Words | 4 Pages
• Natural Forces - 667 Words
Natural Forces A natural force is a power brought on by nature. Natural forces, unlike those of other powers, are uncontrollable. When a hurricane passes along the coast, a bolt of lightning strikes a rooftop, and a volcano erupts, these are all examples of natural forces. Natural forces can have devastating effects on wildlife, humans, and the earth itself. Our effects to resist these occurrences, our only way to cope with such devastating forces of nature are to observe, learn, and...
667 Words | 2 Pages
• Buoyant Forces - 294 Words
Buoyant Forces The purpose of this lab is to calculate buoyant forces of objects submerged in water. The first step in the lab was to measure the mass of a metal cylinder, which was found to be 100g, and then to calculated it's weight, which was .98 newtons. Then next step was to measure the apparent weight of the cylinder when it is completely submerged in a bath of water using the formula Wa=ma*g , this was found to be 88.5grams. Knowing these two numbers, the buoyant force that the...
294 Words | 1 Page
• Normal Force - 802 Words
A ball is thrown upward at time t=0 from the ground with an initial velocity of 18 m/s (~ 40 mph). Assume that g = 10 m/s2. Time to reach apex 18/10 = 1.8 Time x 2 = 3.6 Great height reached by ball – (Velocity)(time)+(-5)(time^2) 18x1.8+(-5)(1.8^2)=16.2 A model rocket accelerates upward from the ground with a constant acceleration, reaching a height of 63 m in 8 s. * Speed at height 63 - 2x63/8 = answer What is the acceleration= answer/8 * If you were to drop a rock from a tall...
802 Words | 4 Pages
• Force and Motion - 1507 Words
﻿ FORCE AND MOTION Ronald Steven DuBois 5th Grade St. Michael's Catholic School 2009 TABLE OF CONTENTS 1. Abstract 2. Introduction 3. Background Information 4. Procedure 6. Data and Observations 7. Results 8. Conclusion 9. Bibliography ABSTRACT I thought it would be fun to fling things like raw eggs and rocks with a catapult. Guess what, it was! By flinging these items I tried to find out if...
1,507 Words | 11 Pages
• Force and Motion - 1054 Words
For other uses, see Force (disambiguation). Page semi-protected See also: Forcing (disambiguation) Force Force examples.svg Forces are also described as a push or pull on an object. They can be due to phenomena such as gravity, magnetism, or anything that might cause a mass to accelerate. Common symbol(s): F, F in SI base quantities: 1 kg·m/s2 SI unit: newton Derivations from other quantities: F = m a Classical mechanics History Timeline Branches[show]...
1,054 Words | 4 Pages
• Force Analysis - 443 Words
FORCE ANALYSIS: Truss & Frame Method of Submission: Paper Copy Q1. Find the force of GJ and state that this member is intension or compression Q2. Determine the force FCG (Tension or compression) Q3. The lift shown is used to elevate motorcycles during manufacture and repair. The hydraulic cylinder OM remains at the 60o angle as the elevation angle  varies. The figures ACDE and FHIJ (J hidden) are parallelograms. There is a ball-and socket joint at M to allow rotation of the frame...
443 Words | 2 Pages
• Centripetal Force - 509 Words
﻿IB PHYSICS HL Lab: Centripetal Force BACKGROUND/PURPOSE: *In this section of your lab write-up, be sure to include all equations and background information -For motion along a straight line, a constant net force F acting on a body of mass m produces a constant acceleration a, related to the force through Newton's law: F = ma -When the same object is moving in a circle at a constant speed, the acceleration of the object is given by the following equation: a = v2/r -In this experiment,...
509 Words | 3 Pages
• Centrifugal Force - 543 Words
| Introduction to | Circular Motion | | Physics | | | HomeNewton's LawsMomentum & ImpulseProjectile Motion & Mechanical EnergyCircular MotionLinks & Extras | IntroductionIn uniform circular motion the magnitude of the velocity of the object in motion remains constant. For example at car turning around a circular curve will stay at 12 m/s throughout the entire turn (provided the driver does not brake). The direction of the velocity vector is changing. A force is required in...
543 Words | 2 Pages
• Force Vector - 2682 Words
Engineering Mechanics: Statics in SI Units, 12e 2 Force Vectors Part 2 Copyright © 2010 Pearson Education South Asia Pte Ltd Chapter Objectives • Cartesian vector form • Dot product and angle between 2 vectors Copyright © 2010 Pearson Education South Asia Pte Ltd Chapter Outline 1. 2. 3. 4. 5. Cartesian Vectors Addition and Subtraction of Cartesian Vectors Position Vectors Force Vector Directed along a Line Dot Product Copyright © 2010 Pearson Education South Asia Pte...
2,682 Words | 16 Pages
• Forces lab - 601 Words
Abstract: The previous lab explored the effect of gravity on free fall. It was determined that acceleration is always constant under free fall. However, in this lab, acceleration was observed under different forces, other than just gravity. Therefore, depending on how strong the forces being exerted were, acceleration differed. It wasn’t constant anymore. Using a glider on a air track and a pulley, different masses were attached at the end of the string and the glider was allowed to move on the...
601 Words | 2 Pages
• Force Daigrams - 501 Words
Questions: 1. Read each description below. Choose the force diagram (free-body diagram) that best represents the description. The forces are acting on the object in red type. You may neglect the effects of air resistance. | A. Mindy's Christmas tree ornament hangs motionless on a tree. | B. Corey's Christmas tree ornament is falling to the floor. | C. A ball thrown by Ginger is moving upward through the air. | D. A ball dropped by Melissa is falling downward toward the floor. |...
501 Words | 2 Pages
• Force and Acceleration - 2331 Words
﻿05-1 SAMPLE PROBLEMS: 111‑SET #5 NEWTON'S 2ND LAW (1‑D MOTION PROBLEMS): 1) A 90 kg woman stands in an elevator. Find the force which the floor of the elevator exerts on the woman a) when the elevator has an upward acceleration of 2 m/sec2; b) when the elevator is rising at constant speed; c) when the elevator has a downward acceleration of 2 m/sec2. Solution: We have a simple application of Newton's 2nd Law of motion. We need only draw the vector force diagram for all forces...
2,331 Words | 11 Pages
• Triangle of Forces - 915 Words
SPACE AND VECTOR DIAGRAMS Table of Contents AIM....………....................................................................................................................... 3 INTRODUCTION………....…………………………........................................................ 3 EQUIPMENT and COMPONENTS USED ........................................................................ 3 EXPERIMENTAL METHOD AND PROCEDURE .......................................................... 3 FINDINGS and RESULTS...
915 Words | 5 Pages
• ﻿Centripetal force - 10485 Words
10,485 Words | 51 Pages
• Forces for Change - 356 Words
Forces for Change It is important for organizations to be open to change and know how to deal with it. Many organizations fail to recognize change causing the organization to suffer and sometimes come to an end. There are six forces that stimulate change in an organization, nature of the workforce, technology, economic shock, competition, social trends, and world politics. The consequences of these economic shocks are bankruptcy, elimination and sometimes acquisition of organizations causing...
356 Words | 2 Pages
• Force and Pressure - 349 Words
Physics holiday homework Applications of Newton’s laws of motion Newton's laws of motion are three physical laws that form the basis for classical mechanics. They describe the relationship between the forces acting on a body and its motion due to those forces. They have been expressed in several different ways over nearly three centuries, and can be summarized as follows: 1- The first law states that an object continues in its state of rest or uniform motion in a straight line unless...
349 Words | 1 Page
• Centrifugal Force - 2117 Words
Centrifugal force Centrifugal force (from Latin centrum, meaning "center", and fugere, meaning "to flee") is the apparent outward force that draws a rotating body away from the center of rotation. It is caused by the inertia of the body as the body's path is continually redirected. In Newtonian mechanics, the term centrifugal force is used to refer to one of two distinct concepts: an inertial force (also called a "fictitious" force) observed in a non-inertial reference frame, and...
2,117 Words | 8 Pages
• Shear Force - 1838 Words
CEMB 121 MECHANICS OF MATERIALS LABORATORY EXPERIMENT (NO.2 (a)) SHEAR FORCE I SUMMARY Shear Forces occurs when two parallel forces act out of alignment with each other. For example, in a large boiler made from the sections of sheet metal plate riveted together, there is an equal and opposite force exerted on the rivets, owing to the expansion and contraction of the plates. The shearing force (SF) at any section of a beam represents the tendency for the portion of the beam on one side...
1,838 Words | 7 Pages
• Centripetal Force - 559 Words
Title: Centripetal Force Tools and Equipments: nylon cord, different weighing hanging masses, stopwatch, meter stick. Purpose: To be able to determine the relationship between centripetal force, mass, velocity, and the radius of orbit for a body that is undergoing centripetal acceleration. To investigate the dynamics of uniform circular motion. Specifically the relationships among the centripetal force, the accelerated mass and the radius of rotation. Procedure: THEORY:...
559 Words | 3 Pages
• Centripetal Force - 649 Words
Centripetal force (from Latin centrum "center" and petere "to seek") is a force that makes a body follow a curved path: its direction is always orthogonal to the velocity of the body, toward the fixed point of the instantaneous center of curvature of the path. Centripetal force is generally the cause of circular motion. In simple terms, centripetal force is defined as a force which keeps a body moving with a uniform speed along a circular path and is directed along the radius towards the...
649 Words | 2 Pages
• The Use of Force - 416 Words
The doctor in "The Use of Force" is very unprofessional. He describes the patient in a very infatuated way. The doctor also abhors the way the parents of the patient referred to him. And the doctor treats the patient aggressively. From the moment the doctor enters the house. He introduces the girl to us in an infatuated sense. He saw her as a "very attractive little thing" and he described her to have "magnificent blonde hair one of those picture children often reproduced in...
416 Words | 1 Page
• Force and Diagram - 2404 Words
1 1 A wooden block of mass 0.60 kg is on a rough horizontal surface. A force of 12 N is applied to the block and it accelerates at 4.0 m s –2. 4.0 m s–2 wooden block 12 N What is the magnitude of the frictional force acting on the block? A B 9.6 N C 14 N D 2 2.4 N 16 N A submarine descends vertically at constant velocity. The three forces acting on the submarine are viscous drag, upthrust and weight. Which relationship between their magnitudes is...
2,404 Words | 36 Pages
• Force Table - 3059 Words
Instruction Manual and Experiment Guide for the PASCO scientific Model ME-9447 012-04715 4/96 Revision B Force Table PASCO scientific CAUTION CAUTION Model Me-9447 FORCE TABLE Copyright © November 1991 \$5.00 Force Table 012-04715B Table of Contents Section Page Copyright andWarranty .................................................................................... ii Equipment Return ............................................................................................. ii...
3,059 Words | 36 Pages
• Force and Motion - 10362 Words
JPN Pahang Physics Module Form 4 Chapter 2 : Force and Motion 2. 2.1 1. FORCE AND MOTION ANALYSING LINEAR MOTION Types of physical quantity: has only a magnitude (i) Scalar quantity: …………………………………………………………………. has both magnitude and direction (ii) Vector quantity: ………………………………………………………………… The difference between distance and displacement: length of the path taken (i) Distance: ………………………………………………………………………… distance of an object from a point in a certain direction (ii) Displacement:...
10,362 Words | 48 Pages
• Centripetal Force - 642 Words
Experiment: Uniform circular motion and centripetal force Results Mass(kg) | Radius(m) | Velocity(m/s) | CentripetalForce[Calculation](kg. m/s2) | CentripetalForce[Measure](kg. m/s2) | StandardDerivation(%) | 0.02406 | 0.0900 | 2.023 | 1.094 | 0.7349 | 32.8 | 0.02406 | 0.0900 | 2.584 | 1.785 | 1.446 | 19.0 | 0.02406 | 0.0900 | 3.153 | 2.658 | 2.351 | 11.4 | 0.02406 | 0.0900 | 3.702 | 3.662 | 3.374 | 7.86 | 0.02406 | 0.0900 | 4.238 | 4.801 | 4.525 | 5.75 | Force versus Mass...
642 Words | 3 Pages
• Force and Acceleration - 1165 Words
questions: force and motion I problem 1 The figure below is an overhead view of a 12 kg tire that is to be pulled by three ropes. One force (Fl, with magnitude 50 N) is indicated. Orient the other two forces F2 and F3 so that the magnitude of the resulting acceleration of the tire is least, and find that magnitude if (a) F2 = 30N, F3= 20 N; (b) F2= 30 N, F3 = 10 N; and (c) F2 = F3 = 30 N. problem 2 A weight-conscious penguin with a mass of 15.0 kg rests on a bathroom scale (see figure below)....
1,165 Words | 3 Pages
• Motion and Force - 456 Words
2 page essay “How does Motion and Forces help your everyday life?” All your life, forces has been acting on you even though you probably didn’t notice it. When you use your pencil, type, walk, or even when your doing something your using force. Those were a few examples of everyday life because, that’s what a force is “everyday life”. Everyday you use force to make your life easier. The correct definition of “Force” is a push or a pull. I’ve always...
456 Words | 2 Pages
• Forces Friction - 868 Words
Forces Have you ever wondered how forces link to our life? Everything we’ve learned in science has got me thinking about it. Forces are an essential part of our daily lives. Forces act on all objects. And we need force for everything we do, whether it’s a push, pull or twist. Force gives an object the energy to move, stop moving or change direction. Newton’s first law states that an objects velocity cannot change unless it is acted upon by a force. Here are examples of force in everyday life....
868 Words | 3 Pages
• Five Forces - 1062 Words
“Rift Deepens as N.B.A Draws Line on Compensation” The N.B.A. is a well established association and is well-known across the globe. Over the past couple months the association has been in contract talks between the players union and the N.B.A. officials. With the basketball season right around the corner, both sides have been able to work out an agreement to get the players back on the court playing the game they love. As Porter’s “Five Forces” model describes how certain areas of the...
1,062 Words | 3 Pages
• Competing forces - 833 Words
How competitive forces shape strategy Pﬂicht 4. (5Forces) " 1 von 3 While one some- times hears executives complaining to the contrary, intense competition in an industry is neither coincidence nor bad luck. Moreover, in the fight for market share, competition is not manifested only in the other players. Rather, competition in an industry is rooted in its underlying economics, and competitive forces exist that go well beyond the established combatants in a particular industry....
833 Words | 5 Pages
• Polygon of Forces - 1822 Words
Abstract Static equilibrium of forces was investigated through the use of different weights attached to cords which were connected to a central ring, while pulleys supported them. This assembly facilitated the force band system to demonstrate that equilibrium will be attaining regardless of disturbances. However, due to errors in the experiment, the sum of the x and y component did equate to zero as predicted. The graphical solution of the experiment yield a polygon that is completed...
1,822 Words | 11 Pages
• Shear Force - 520 Words
TITLE : Shear Force Variation with an Increasing Point Load. INTRODUCTION: SHEAR FORCE The shearing force (SF) at any section of a beam represents the tendency for the portion of the beam on one side of the section to slide or shear laterally relative to the other portion. The diagram shows a beam carrying loads . It is simply supported at two points where the reactions are Assume that the beam is divided into two parts by a section XX The resultant of the loads and reaction acting...
520 Words | 4 Pages
• force vector - 306 Words
"The Force Table" is a simple tool for demonstrating Newton’s First Law and the vector nature of forces. This tool is based on the principle of “equilibrium”. An object is said to be in equilibrium when there is no net force acting on it. An object with no net force acting on it has no acceleration. By using simple weights, pulleys and strings placed around a circular table, several forces can be applied to an object located in the center of the table in such a way that the forces exactly cancel...
306 Words | 1 Page
• Impulsive Force - 489 Words
[pic] The product of average force and the time it is exerted is called the impulse of force. From Newton's second law [pic] the impulse of force can be extracted and found to be equal to the change in momentum of an object provided the mass is constant: |[pic] |Calculation | The main utility of the concept is in the study of the average impact force during collisions. For collisions, the mass and change in velocity are...
489 Words | 3 Pages
• Force and Spring - 501 Words
﻿Masses and Springs 1. Spring Constant K1 = F/x1 = (.05kg)(9.8 N/kg) = 9.8 N/m .05m K2 = F/x2 = (.1kg)(9.8 N/kg) = 9.8 N/m .1m K3 = F/x3 = (.25kg)(9.8 N/kg) = 9.8 N/m .25m K avg. = 9.8 N/m 2. Unknown Masses Green: m = kx = 9.8 * .07 = .07kg = 70g g 9.8 Gold: m = kx = 9.8 * .155 = .155kg = 155g g 9.8 Red: m = kx = 9.8 * .3...
501 Words | 2 Pages
• Competitive Forces - 583 Words
Competitive Forces (Porter's 5 Forces) Analysis of the competitive environment can be done utilising Michael Porter's 5-forces model of UPS and FedEx. Porter's theoretical framework allows us to determine the overall profitability and sustainability within the industry (Laudon & Laudon 2006, pg.99; Hubbard 2004, pg.211). We reckon that in this case, the competitive forces for both UPS and FedEx are very similar because they are both in the same industry.  Power of substitutes:...
583 Words | 2 Pages
• Hydrostatic Force - 1266 Words
HYDROSTATIC FORCE (EXPERIMENT 1) INTRODUCTION The determination of force which are exerted by liquid which are at rest on surface immersed in liquids. From the study by hydrostatic, the following principles have been established : a) There are no shear stress present when the fluid is not in motion. b) The pressure exerted by a fluid under hydrostatic conditions. This pressure acts perpendicular to an immersed surface. c) Hydrostatic pressure various linearly, increasing with...
1,266 Words | 6 Pages
• Definition of Force - 1890 Words
Definition of Force A force is a push or pull upon an object resulting from the object's interaction with another object. Whenever there is an interaction between two objects, there is a force upon each of the objects. When the interaction ceases, the two objects no longer experience the force. Forces onlyexist as a result of an interaction. Velocity, Acceleration, Momentum, and Impulse Velocity, in physics, is a vector quantity (it has both magnitude and direction), and is the time rate...
1,890 Words | 7 Pages
• Aerodynamics: Force and Ball - 313 Words
When you hear the word aerodynamics, the first thing that comes to mind is airplanes and pilots. There are other applications that apply. For instance, the passing of a football. A football that is thrown into the air has inertia. This is the tendency of an object in motion to remain in motion. But because of gravity the ball is pulled down and resistance that slows the ball down. A quarterback through the motions of his and body, must balance the forward momentum that he gives the ball,...
313 Words | 1 Page
• Porters Five Force - 810 Words
Main Aspects of Porter’s Five Forces Analysis The original competitive forces model, as proposed by Porter, identified five forces which would impact on an organization’s behaviour in a competitive market. These include the following: • The rivalry between existing sellers in the market. • The power exerted by the customers in the market. • The impact of the suppliers on the sellers. • The potential threat of new sellers entering the market. • The threat of substitute...
810 Words | 4 Pages
• Force and Kinetic Energy - 814 Words
Part B Now, suppose that Zak's younger cousin, Greta, sees him sliding and takes off her shoes so that she can slide as well (assume her socks have the same coefficient of kinetic friction as Zak's). Instead of getting a running start, she asks Zak to give her a push. So, Zak pushes her with a force of 125 \rm N over a distance of 1.00 \rm m. If her mass is 20.0 \rm kg, what distance d_2 does she slide after Zak's push ends? Remember that the frictional force acts on Greta during Zak's push...
814 Words | 3 Pages
• Equilibrium: Force Table - 1336 Words
Abstract Equilibrium is the condition of a system in which competing influences are balanced. In the experiment we measured and experimented for the equilibrant force, conditions and center of gravity. Our results showed consideration as to disregarding other forces than weight and tension. 1. Introduction Equilibrium is a state of balance in which it is a condition where there is no change in the state of motion of a body. Equilibrium may be observed on objects which are at rest and...
1,336 Words | 5 Pages
• G Force in Physics - 1092 Words
﻿http://www.physicsclassroom.com/mmedia/circmot/rcd.cfm What is ‘g force’ in physics? G, in physics, a symbol relating to gravity. A capital G indicates the gravitational constant, as explained in the article GRAVITATION. A lower-case g stands for the acceleration imparted by gravity at the earth's surface. An acceleration of 1 g is 32. 1 feet per second per second (9.8 m/s2). Fliers and astronauts may experience accelerations many times larger than 1 g. These accelerations are usually...
1,092 Words | 4 Pages
• CENTRIPETAL FORCE ON A PENDULUM - 766 Words
﻿CENTRIPETAL FORCE ON A PENDULUM OBJECTIVE To measure centripetal force exerted on a pendulum using the force sensor bob and in so doing compare this value determined by force calculations based on the height of the pendulum. THEORY Newton’s laws of motion are the basis for this experiment. Newton’s first law of motion states that a body in motion will remain in motion unless acted upon by an external force. Newton’s second law of motion states that the rate of momentum of a body is dependent...
766 Words | 3 Pages
• Studying Force of Friction - 1226 Words
A1 Studying force of friction Objective To investigate the effect on friction of the following factors: 1. normal force that presses the two surfaces together 2. materials that the two surfaces are made of 3. area in contact of the two surfaces Apparatus Rectangular wooden block Wooden plank Glass plate Plastic plate String Scissors Jack Spring balance Electronic balance Half-meter rule Retort stand and clamp G-clamp Trolley[pic]2 Standard weights (100g)[pic]5...
1,226 Words | 6 Pages
• Force and Class Date - 903 Words
Name ___________________________ Chapter 2 Class __________________ Date ____________ Mechanical Equilibrium Exercises 2.1 Force (pages 13–14) pull push 1. A force is a or a . motion of an 2. A force is needed to change the state of object. 3. Is the following sentence true or false? If an object is sliding on ice, it will true continue sliding until a force slows it down. 4. Define net force. the combination of all forces acting on an object Applied Forces d...
903 Words | 7 Pages
• Forces on Incline and Flat Surface
﻿Lab: Forces on Incline and Flat Surface. Pushing on a flat surface: Hypothesis: There will be a direct correlation between the mass added to the newton meter and the reading. Materials: 1. Several Masses 2. Scale 3. Newton-meter 4. Flat surface Procedure: 1. Place a chosen amount of mass on the flat surface 2. Pull the object with the newton meter until it begins to move 3. Record the data 4. Repeat steps 1-3 for different masses Data/Results: See Excel Table and Graph 1....
288 Words | 2 Pages
• porters five forces - 495 Words
﻿Porters 5 forces Threat of New Entry: Obesity is a big problem in the United States which is becoming a government and healthcare issue. Weight Watchers has played a role in the development of a new national awareness of healthful eating, lifestyles changes, and weight control. Weight Watchers International had experienced it biggest threat mostly because of new competition and changes in technology. When the over the counter weightless drug launched it had a drastic effect on their market....
495 Words | 2 Pages
• Force and Movie Batman Leaps
Superheroes have been around for a time now, since 1934 starting with Mandrake the Magician made by Lee Falk, and then came Superman made by Joe Shuster and Jerry Siegel. But how do superheroes do what they do? They play mind tricks, can lift up incredible amounts of weight and do stuff no regular human can do. In this paper I’m writing you will see how superheroes violate Newton’s 3 laws of motion. First let’s talk about batman and the movie that just came out called the dark night rises. In...
445 Words | 1 Page
• measure and calculate the centripetal force
Physics Lab Outline Objectives: The objective is to measure and calculate the centripetal force. Theory: Gravity is caused by the manual attraction of two objects. This mutual attraction will cause objects to fall tot eh earth at a rate of 9.8 meters per second per second, near the surface of the earth. Procedures: First, I had to determine the mass of the spinning projectile. Once the mass was determined I then arranged the copper tube, twine, hanger and mass. When arranging I made sure...
507 Words | 2 Pages
• Shear Force Acting on Beams
qwertyuiopasdfghjklzxcvbnmqw ertyuiopasdfghjklzxcvbnmqwert yuiopasdfghjklzxcvbnmqwertyu iopasdfghjklzxcvbnmqwertyuio Shear Force Experiment pasdfghjklzxcvbnmqwertyuiopa Submitted to : Sir Raees Fida Swati sdfghjklzxcvbnmqwertyuiopasdf ghjklzxcvbnmqwertyuiopasdfghj klzxcvbnmqwertyuiopasdfghjklz xcvbnmqwertyuiopasdfghjklzxc vbnmqwertyuiopasdfghjklzxcvb nmqwertyuiopasdfghjklzxcvbn mqwertyuiopasdfghjklzxcvbnm qwertyuiopasdfghjklzxcvbnmqw ertyuiopasdfghjklzxcvbnmqwert yuiopasdfghjklzxcvbnmqwertyu...
1,198 Words | 6 Pages
• Internal Forces in Beams - 330 Words
Types of Loads 1- Concentrated load assumed to act at a point and immediately introduce an oversimplification since all practical loading system must be applied over a finite area. 2- Distributed load are assumed to act over part, or all, of the beam and in most cases are assumed to be equally or uniformly distributed. a- Uniformly distributed load. a- Uniformly varying load. Concept of Shear Force and Bending moment in beams: When the beam is loaded in some...
330 Words | 2 Pages
• Equilibrium of Parallel Force - 624 Words
Physics lab:9 Equilibrium of parallel force 11/09/2012 By: Camilo Salazar Jillian Ellis Purpose: To understand the conditions need for a rigid body to be in equilibrium when there are forces acting on the body from different sides. Theory: When force is applied on a rigid body for example a ruler it can either be in equilibrium or it can be unbalance. When the force is unbalance what would happen is this motion the body can be either translational or rotational. “A body in...
624 Words | 2 Pages
• Porter's five forces - 590 Words
Porter’s 5 Forces Analysis = Suppliers, Customers, New Entrants, Substitute Products, Competitors What is Porter’s 5 Forces Analysis? Porter’s 5 forces analysis represents the competitive environment of the firm. It is a strategic foresight to avoid putting the competitive edge at risk and ensure the profitability of products on a long term. For the company this vision is quite important because the firm is able to direct its innovations in terms of choice of strategies and investments....
590 Words | 3 Pages
• Force vs Area - 1274 Words
Force vs. Area Connor Blackmon Chemistry I H, 1st Period Mrs. Kris Clements October 18, 2012 Problem Will a balloon pop if it is places on a bed of nails and pressure is applied? Hypothesis If a balloon is placed on a bed of nails and a force is applied, then the balloon will burst. Variables Independent variable- Force applied to the balloon and number of nails Dependent variable- Does the balloon burst? Materials 14 inch by 14 in by .75 in plywood board x2...
1,274 Words | 5 Pages
• (Physics Force for Lawn Beautification)
(Physics force for lawn beautification) Community based physics activity (Physics force for lawn beautification) In partial fulfillment in Physics for health science Submitted to; Mrs. Susan Matipo, PhD. Submitted by: Romulo Garrote Mayrose Balintona Rizel Gamurot Liezel Bucao Rosario Ambala Melody Bago Edmar Luban INTRODUCTION As we think of physic, we always associate it with problem solving, formulas and performing mathematical theorems. But come...
1,046 Words | 5 Pages
• Accountability in the Police Force - 389 Words
Accountability Legal Accountability: this means you have to follow the law that has been made at all times and you have to be seen as following the law. The police enforce this is taken very strictly. For example, the police have the: • Authority whose job is to oversee their work • Inspections by the Queens inspectors • Inspection by the Adult Commission • The independent Police Complaints Commission • The media, as they will publicise and may even twist things up to make it sound worse...
389 Words | 2 Pages
• Centripetal Force Lab Activity
Centripetal Force Lab Activity Analysis: 1. A) Average Percent Difference: 50g: (values expressed in newtons) Step 1: Calculate the average value of the two variables Average Value= Value 1+ Value 2 /2 = 0.49+ 0.61/2 = 1.1/2 = 0.55 Step 2: Calculate the difference between the two variables Difference= Value 2- Value 1 = Fc- Fg = 0.61- 0.49 = 0.12 Step 3: Calculate % difference % difference=...
1,634 Words | 7 Pages
• Drag Force Measurement - 1200 Words
GE322 429101961 GE322 GE322 GE322 EXPERIMENT NO.3: DRAG FORCE EXPERIMENT NO.3: DRAG FORCE 1. Objectives * Calculation of velocity profile in the wake of a two-dimensional cylinder. * Estimate the coefficient of drag and compare with values in the literature and from the force balance. 2. Introduction Drag is an unavoidable consequence of an object moving through a fluid. Drag is the force generated parallel and in opposition to the direction of travel for an...
1,200 Words | 5 Pages
• Force and Perfectly Elastic Question
﻿Test1 Question no 9) A package is dropped from a helicopter moving upward at 15m/s If it takes16 sec before the package strikes the ground, how high above the ground was the package when it was released if air resistance is negligible? Ans) 1000m Question no. 11) If A -B = 0, then the vectors A and B have equal magnitudes and are directed in the opposite directions from each other. Ans) False Question no. 16) A monkey is sitting at the top of a tree 20 m above ground level. A person standing...
857 Words | 3 Pages
• Force and Portion Ac - 544 Words
Assignment 3 ES230 Key solutions Problem 3.1 | | | | |A 90-N force is applied to the control rod AB as shown. Knowing that the length of the rod is | | |225 mm, determine the moment of the force about point B by resolving the force into...
544 Words | 7 Pages
• Force Practice Questions - 410 Words
A hockey stick exerts an average force of 39N on a 0.2kg hockey puck over a displacement of 0.22m. if the hockey puck started from rest, what is the final velocity of the puck? Assume no friction. Your physics teacher walking with the aid of a cane approaches a skateboard of 3.5 kg lying on the side walk. Pushing with an angle of 60 degree down from the horizontal with his cane, he applies a force of 115N, which is enough to toll the skateboard out of his way. Calculate the initial...
410 Words | 2 Pages
• Porters Five Forces - 461 Words
PORTERS FIVE FORCE MODEL Porter’s Five force model includes 4 forces: * Potential Entrants(Threat Of Mobility) * Buyers(Buyer Power) * Substitutes(Threat Of Substitutes) * Suppliers(Supplier Power) * Industry Rivalry Application on the Telecom Industry: The forces that affect the Telecom Industry:- INDUSTRY RIVALRY: The above shows the different market share of the different firms such as Airtel which holds 28% of the total share being the highest , Vodaphone...
461 Words | 2 Pages
• 5 Industry Forces - 678 Words
﻿ Competition is all around us. This can be in the form of sports, popularity, achievements, and also in business. We are constantly being bombarded with advertisement on top of advertisement where some brand or company is trying to make us believe that theirs is the biggest and best, the one we’ve been missing. Beyond the radio ads and TV commercials are the main competitive forces behind that competition and that is what I would like discuss in the next few paragraphs. Before I go...
678 Words | 2 Pages
• Physics Force Notes - 2382 Words
2,382 Words | 9 Pages
• The Use of Force Analysis - 413 Words
Level One  The Use of Force is about a girl who may have Diphtheria, but refuses to open her mouth to let the doctor look at her throat. After much struggle, emotional and physical, the doctor forces her to open her mouth and it turns out she does indeed have the disease. Level Two  Setting  It's not actually mentioned, but it is implied that it at the Olson's house, a doctor is called to look at the daughter as she is not feeling well.  The Characters  o The parents are pretty static...
413 Words | 2 Pages
• Force and Free Body Diagram
ASSIGNMENT 2 DUE DATE: 4 DECEMBER 2012 (Submit into Mr. Ng Poh Kiat’s pigeon box) Instructions: This is an individual assignment. Answer both Section A and Section B. Your answers MUST be in written form. Marks will be deducted if printed copies, photocopies or electronic formats are submitted. Please submit only the answer sheet with your name and student ID on it. Marks will be deducted for late submission. Section A (6 marks) 1. What is the definition of mass? A. How much...
442 Words | 3 Pages
• Bending Moment and Shearing Force
INTRODUCTION Basic structural learning begins with an analyzing of a simply supported beam. A beam is a structural member (horizontal) that is design to support the applied load (vertical). It resists the applied loading by a combination of internal transverse shear force and bending moment. An accurate analysis required in order to make sure the beam is construct without any excessive loads which affect its strength. A bending moment exists in a structural element when a moment is applied...
1,013 Words | 10 Pages
• Physics Notes (Forces) - 665 Words
Physics notes Force is an agent which produces or tends to produce motion in an object, stops or tends to stop , motion of an object Newton's 1st law of motion: If an object is at rest, will remain at rest until or unless an external force act on it. If an object is in motion , it continues its motion until or unless an external force act on it Newton's 1st law of motion is also called first law of inertia. Inertia: The tendency of an object to resist any change in its state of...
665 Words | 3 Pages
• Force and Lb B. - 1108 Words
1. Which of the following sets of horizontal forces could leave an object in equilibrium? a. 25, 50 and 100 N b. 5, 10, 20 and 50 N c. 8, 16, and 32 N d. 20, 20 and 20 N 2. Which of the following sets of horizontal forces could not leave an object in equilibrium? a. 6, 8 and 10 lb b. 10, 10 , and 10 lb c. 10, 20 and 30 lb d. 20, 40 and 80 lb 3. If an object is free to move in a plane, the number of scalar equations that must be satisfied for it to be...
1,108 Words | 5 Pages
• Friction: Force and Mass - 614 Words
Purpose: To study sliding friction and to determine the coefficients of static and kinetic friction. Theory: Friction is a force that opposes motion. Static friction prevents an objects being set into motion by an external force. Kinetic friction opposes the progress of a sliding object. Static friction is given by Fs< usn where N is the normal force between the object and its support surface and us is the coefficient of static friction. There-fore, the coefficient of static friction is...
614 Words | 2 Pages
• Force and Torsional Shear Stress
CE 270 - Final Exam Problem No. 1. (20 points) A rectangular cross-section that is 50 mm wide and 250 mm deep is subjected to shear force of 22 kN, axial force (tension) of 16.5 kN and bending moment of 33 kN-m. Calculate and show the stress diagrams in the cross-section. What is the maximum normal stress, and where does it occur. What is the maximum shear stress and where does it occur. Problem No. 2 (20 points) Determine the principal stress, the maximum in-plane shear...
413 Words | 2 Pages
• Effect of Force and Mass on Acceleration
The Effects of Force and Mass on an Object’s Acceleration Abstract: In this lab there were two principals investigated. The first was the relationship between applied force and acceleration. The second was the relationship between mass and acceleration. To study these two relationships, my partners and I used a dynamic cart with added mass on it. This cart was then attached to a pulley system on a “frictionless track” where it was pulled by a string bearing mass over the...
1,874 Words | 6 Pages
• Force and Lever Arm - 749 Words
1. What are the two types of friction that affect the performance of your vehicle? The first type of friction that affects the mousetrap car is called rolling friction. This type of friction occurs in between the wheels of the car and the surface of the ground it moves on. The second type is called the sliding friction which occurs in between the axles and the brackets. 2. What problems related to friction did you encounter and how did you solve them? We noticed that at times the car would...
749 Words | 2 Pages
• Physics Lab force - 1047 Words
Objective: To study the relationships between position, velocity, and time, with acceleration held constant, of an object moving in one-dimensional motion with minimum friction. A motion sensor will be used to measure various aspects of vector quantities. Description: An Air Track is positioned along the edge of the table. It is a long straight metal beam with many small holes that are roughly each 2mm in diameter. It is positioned at an angle to allow the gliders to glide down the...
1,047 Words | 4 Pages
• Michael Porter 5 Forces
Title: Michael’s Porter’s five competitive forces in business Business is a form of system that exchanged services or goods with money. When we commence a business in Singapore, we have to invest in that business with efficient capital. Successful businesses enable us to gain profit and expand our business to a larger size. Therefore, there are a few principles that we must comply. The most basic principle would be the Michael Porter’s five competitive forces. Firstly, the most major force...
467 Words | 2 Pages
• Equilibrium: Force and Mg - 1770 Words
The First and Second Conditions for Equilibrium The first condition for equilibrium: The second condition for equilibrium: • • ΣF = 0 ΣΓ = 0 • In when both of these conditions are satisfied in static systems all forces and torques sum to zero. In problems where the first and second conditions of equilibrium are satisfied, the best strategy is to create FBD’s for both the first and second conditions, derive equations based on these FBD’s and then see what useful information may be gleaned...
1,770 Words | 12 Pages
• Four Forces of Flight - 892 Words
When it comes to airplane travel, that is pretty much our experience. We are more concerned about comfort, available amenities, and food. We see them every day: airplanes, jets, and helicopters, soaring, zooming, and even roaring through the skies, but how many you actually have sat back and indulged yourself in the physical amazement of how a 975,000 lb. ballerina, like a 747 jumbo jet, leaps up into the atmosphere, and when its time, settles so graciously back to the bondages of terra firma?...
892 Words | 3 Pages
• Force and Total Organization Change
﻿1. Managers have to deal with two types of change – reactive and proactive. Define each of these types. Which type of change occurred at H&B? Reactive change involves making changes in response to problems or opportunities as they rise. Proactive change involves making carefully considered changes in hope of possible or expected problems or opportunities. Clearly, Hillerich was dealing with reactive change at H&B. Dysfunction among the company’s internal systems and weakening support for...
274 Words | 1 Page
• Centripetal Force Lab Report
Purpose To be able to understand and verify the relationship centripetal force, mass, velocity, and the radius of orbit for a body that is undergoing centripetal acceleration. Background Information An object moving in the same direction is not necessarily undergoing acceleration. If the object changes speed while moving in the same direction there is acceleration (or deceleration). On the other hand, if the object moves at a constant speed in the same direction, there is no...
1,348 Words | 7 Pages
• Force Table Writing Sample
Comparing Forces Measured with a Force Table Experimentally, we observe that the three forces applied to the ring in the center of the Force Table balance. If forces are vectors, we expect the vector sum of these three forces to equal zero. Experimental uncertainties will generally produce a small nonzero sum. If the magnitude of the sum of the three vectors is not much greater than the expected uncertainties, the measured force vectors can be said to add like true vectors. Because the...
300 Words | 1 Page
• Porter's five forces - 582 Words
1. Porter have developed five forces, basically it is a framework to analyze the level of competition within an industry in order to develop a business strategy. The first force as what Porter defined is the threat of new entrants, which can eventually decrease the profitability for all firms in their particular industries. This happens whenever profitable markets yield high returns that can attract new firms. The second force is the threat of substitute products or services or products, this is...
582 Words | 2 Pages
• Force and Mechanical Advantage: A Test
﻿Name: payton gratehouse Date: Graded Assignment Unit Test, Part 2 Answer the questions, using complete sentences. When you have finished, submit this assignment to your teacher by the due date for full credit. (8 points) Score 0. A sailboat moves north for a distance of 10.00 km when blown by a wind from the exact southeast with a force of 2.00 × 104 N. The sailboat travels the distance in 1.0 h. How much work was done by the wind? What was the wind’s power? Your response should include all...
361 Words | 2 Pages
• Force and Behavioral Inertia - 499 Words
Inertia Inertia is the tendency for a body to either remain at rest or move in a straight line at a constant speed, unless acted up by an unbalanced force. In both cases, the item has an acceleration of zero. Inertia is not a force, but rather a resistance to a change in velocity. In other words, the object wants to stay put or stay constant, and inertia is what happens when a force gives it acceleration. An example of inertia in the physical world happens while riding in a car. The driver...
499 Words | 2 Pages
• Addition of Force Vectors - 308 Words
Addition of Force Vectors Abstract The purpose, of this experiment, was to prove that there is a relation between the magnitude of the resulting vector, and the angle between the vectors that are being added. The test was performed by creating a balance between three weights tied to strings on a pulley that transferred the string on top of a graduated disc, which made easy the measurement of the angles between them. After performing the experiment, my group concluded that there is a...
308 Words | 2 Pages
• Fundamental Forces Of Nature - 1087 Words
Science Notes: Fundamental Forces of Nature All forces in nature may be classified into four types. The gravitational force holds together the universe at large, plus the atmosphere, water, and us to the planet Earth. The electromagnetic force governs atomic level phenomena, binding electrons to atoms, and atoms to one another to form molecules and compounds. The strong nuclear force holds the nucleus together. The fourth force, the weak nuclear force, is responsible for certain types of...
1,087 Words | 5 Pages
• Moving Forces; Human Puppets
﻿Victoria Madeline Byrd English 310 Stacia Gray March 10th 2014 Moving Forces; Human Puppets Humans are malleable. We are but reflections of our experiences and surroundings. We are all but powerless in the grand scheme of things. In two pieces: William Faulkner’s A Rose for Emily and John Updike’s Outage, you see this idea in full affect. Though in principle they are seemingly two very different stories, upon further inspection you see that both have a strikingly similar underlying theme....
1,135 Words | 3 Pages
• Force and Free Body Diagram
Practice Test 1. Which of the following is true for a conservative force? A) The work done by the force is independent of the path between the initial and final positions. B) The NET work done by the force is zero when the object moves around a closed path, starting and finishing at the same point C. The work done by the force equals –ΔPE. D. All of the above. 2. An elevator supported by a single cable descends a shaft at a constant speed. The only forces acting on the elevator...
1,096 Words | 4 Pages
• Volleyball: Force and Momentum - 1078 Words
﻿St Monicas College Volleyball [Type the document subtitle] Nikki Valdez [Pick the date] Intro Throughout this term I have taken photos of my progress with my volleyball serve. I will be showing you in detail my strengths and weaknesses with my volleyball serve. When applying the serve I will be Correcting errors, justifying and analysis using biomechanical terms. Biomechanics applies to the science field in sport. It’s the laws and principals of mechanics about human...
1,078 Words | 3 Pages
• Shear Force and Bending Moment
EXPERIMENT 2 Title : Shear Force and Bending Moment Objective : To determine the shear force and bending moment when concentrated load, symmetrical load and non symmetrical load are applied Introduction The shear force (F) in a beam at any section, X, is the force transverse to the beam tending cause it to shear across the section. The shear force at any section is taken as positive if the right-hand side tends to slide downwards relative to the left hand portion. The...
2,466 Words | 11 Pages
• Force and Constant Velocity - 298 Words
﻿ Force vector. Equilibrium. Moments. 1. Determine the resultant force and state whether the object is at equilibrium. sin52=0.788; cos52=0.616; sin25=0.423; cos25=0.906; sin27=0.454; cos27=0.891; sin26=0.438; cos26=0.899; 2. If the mass of the plane is 1700kg, and drag force is 50kN, determine what should be the aerodynamic lift force and engine’s thrust so that the plane flew with constant velocity. 3. The spring was extended to 3cm under mass of...
298 Words | 2 Pages